The new extender is giving bad wifi results? However, this frustrates everyone a lot. No worries! Yes as you are a few minutes away from extending your Wi-Fi signals to every room of your house or workplace using the Netgear extender.
Web Browser Configuration
There is one more way to get the fastest internet speed and you can do that through the Netgear extender setup. Wait for the LED once you plug the device into the socket in the same room as your router, which must also need to be solid blue. Connect with the extender’s Wi-Fi through your mobile. However, turn off your Mobile Data, open a browsing crawler, and write 192.168.1.1 for the same purpose. The WiFi networks are mandatory to be chosen at the same time.
Change The Location Of The Extender And Try Accessing The WiFi
Just plug the extender into the outlet halfway between the existing router and the Wi-Fi dead zone to get a good performance. But, make sure to be certain about the place you fix for the current WiFi network. Wait until the Signal LED is completely blue. Therefore just connect the Wi-Fi devices with it. The extender and the existing router mostly share the same SSID Netgear_EXT.
Configuration With The WPS Button
For Extender Setup, you have to use the Wi-Fi-protected setup (WPS) button, by doing this you can expand the WiFi networks.
Press the WPS button tightly on the WiFi extender for more than ten minutes. Roughly doing the step could also lead to results. So Wait for the LED signal light to become solid blue.
Set Up With Another Process
If you can’t locate the button, it’s because your existing router lacks it, so you will need to use the second method that will be discussed later in the post to extend your Wi-Fi network). In the beginning like the others just power up the extender to a power source near the router in the same room. But for a strong connection make sure the power is lit Solid blue. Check that the device’s antenna points up and vertically to the ground.
Finally, swap the extender and shift it to another location. Plug the extender into an outlet midway between the router and the Wi-Fi dead zone for optimal performance. You need to be certain about the place while choosing the WiFi Network.
However, you need to wait till the LED becomes solid blue. Then, connect your Wi-Fi devices to it. The SSID of your extender is the same as the SSID of your router but with the suffix Netgear_EXT/5GEXT.
Guide For Troubleshooting Issues
Reset the process of the WiFi extender. To begin the process, turn on the gadget. This simple procedure only needs one sharp pointed pin like a pen or a paper clip. Just hold it on the button for 2-3 seconds tightly, till The PWR LED becomes solid again. When it is solid on, your Wi-Fi extender means it has been reset successfully. See the points to help troubleshoot the errors as well.
Why Can’t I Access The Wi-Fi Extender’s Web Interface?
If you’re using a Wi-Fi device, check to make sure you’re linked to the extender’s Wi-Fi network Netgear, EXT, and that the Mobile Data feature is turned off.
If you use a computer, ensure that you are connected to the extender’s Wi-Fi network of mywifiext.net setup and that your computer is configured to automatically get an IP address and DNS server address.
The Router’s Network Is Unable To Connect To The Extender?
When the router encrypts using WPA or WEP, there is an urgent need to change the encryption to WPA-PSK or WPA2-PSK, after this try to scan the networks again. But the location of the WiFi device matters a lot. Check if the placement of your Netgear device is correct or if it needs improvement. If you are unable to connect to your extender’s network again and again, there is obviously a need for adjustment in the placement of your extender device and the host device as well. Once you adjust the placement, you can move ahead to restart your device and then connect again. You will most likely not face the connection issue again.
What If There Are No Signals
The signal strength of the mobile device will be affected by the location of the device. So double-check to be sure. Verify with the router’s encryption whether it is WEP or not.
So that’s how you get the troubleshooting tips running your extender. In case you find any issue after or between the Setup procedure. Then, you need to reboot the device and begin the procedure again. Generally, there could be a lot of difficulties like the device not working, including a sluggish network and mywifiext.net setup not working.
